201 Search Results

Here, a comparative study of Cr/Au and Ti/Au ohmic contacts on (001) β-Ga₂O₃ was conducted. The electrical behavior from current-voltage measurements and the interfacial composition and microstructure as determined from high-resolution transmission electron microscopy (TEM) with energy dispersive x-ray analysis were compared for the different contacts at selected points in an annealing series (300–700 °C, 1 min. anneals in N₂). Cr/Au contacts became ohmic at temperatures (300–350 °C) approximately 50–100 °C lower than Ti/Au contacts (400–450 °C). Cr/Au and Ti/Au contacts demonstrated optimal ohmic behavior (lowest resistance) when annealed to 450–500 and 500–600 °C, respectively, with Ti/Au contacts yielding amore » lower total resistance than Cr/Au. Cross-sectional TEM images of Cr/Au contacts annealed at 450 °C revealed the presence of Au nanoclusters at the Ga₂O₃ interface and CrO_x layers at both the top of the contact and the Ga₂O₃ interface. Whereas TiO_x also formed at the top and bottom interfaces in 450 °C-annealed Ti/Au contacts, the TiO_x surface layer appeared to be variable in thickness and/or discontinuous, unlike the CrO_x surface layer. Au nanoclusters were not detected at the interface in the Ti/Au contacts. The interdiffusion and oxidation observed in both contact metallizations point to the need for diffusion barriers that may allow these contacts to be used in future Ga₂O₃-based devices that operate at elevated temperatures.« less

Capturing CO₂ at trace concentration remains a critical challenge in sustainable carbon management via adsorption, as conventional adsorbents suffer from low CO₂ selectivity, poor moisture tolerance, and energy-intensive regeneration requirements. Here, we report a hierarchical Ba²⁺-exchanged silicoaluminophosphate (Ba²⁺-CSAPO-34) composite synthesized via confined-space crystallization within an activated carbon matrix. Comprehensive characterization revealed a confined nucleation mechanism and the successful incorporation of Ba²⁺ active sites within the SAPO-34 framework, achieved via a two-step liquid ion-exchange protocol. The core-shell architecture combines the selective CO₂ binding of Ba²⁺-functionalized SAPO-34 with the hydrophobic protection of the carbon shell. Fixed-bed adsorption tests demonstrated strong CO₂ bindingmore » (at 500-2500 ppm), no roll-up, and effective suppression of water affinity, while maintaining high selectivity even at 90% relative humidity. A phenomenological adsorption model, validated against dynamic breakthrough data, accurately predicted dynamic adsorption behavior under real-world operating conditions, enabling rational process design for direct air capture (DAC) and closed-loop life support systems. Furthermore, these results establish Ba²⁺-CSAPO-34 as a scalable, moisture-resistant adsorbent that addresses key limitations in trace CO₂ capture, advancing practical implementation of carbon removal technologies.« less

The structure of plant cellulose microfibrils remains elusive, despite the abundance of cellulose and its utility in industry. Using 2D solid-state NMR of ¹³C-labeled never-dried plants, six major glucose environments are resolved, which are common to the cellulose of softwood, hardwood, and grasses. These environments are maintained in isolated holocellulose nanofibrils, allowing more detailed microfibril characterization. We show that there are only two glucose environments that reside within the microfibril core. These have the same NMR ¹³C chemical shifts as tunicate cellulose Iβ center and origin chains, with no cellulose Iα being detected. The third major glucose site within spectralmore » domain 1, previously assigned to the crystalline microfibril interior, is in close proximity to water, which could indicate that it is a surface glucose environment. The NMR peak widths of all four surface glucose environments are similar to those of the core, indicating that their glucose local order is comparable; there is no significant “amorphous” cellulose in the microfibrils. Consequently, the ratio of the carbon 4 peaks at ∼89 and ∼84 ppm, which has often provided a sample cellulose crystallinity index, is not a meaningful measure of fibril crystallinity or the interior to surface ratio. The revised ratio for poplar wood microfibrils is estimated to be 1:2, which is consistent with an 18-chain microfibril having 6 core and 12 surface chains, although other microfibril sizes are possible. These advances substantially change both the interpretation of solid-state NMR studies of cellulose and the understanding of cellulose microfibril structure and crystallinity.« less

Accurate, passive, and wireless monitoring of cryogenic hardware is essential for high-energy physics, space propulsion, and biomedical instrumentation. Here, this study quantifies the coupled temperature-strain behavior of Rayleigh-mode surface acoustic-wave (SAW) delay-line sensors fabricated on 128° YX-cut LiNbO₃. A nonlinear finite element (FE) model incorporating Varshni-based elastic constants, higher-order thermal expansion, and temperature-dependent piezo- and dielectric coefficients was developed and validated experimentally between 280K and 80K. Free-standing (first test condition) and bonded/wired (second test condition) devices exhibited indistinguishable thermal responses; the average temperature coefficient of delay (TCD) in the critical cryogenic range from 130K down to 80K differed by onlymore » 0.15 ppm/K (0.32%), confirming that bonding-induced stress is negligible. Over 280-80K the measured TCD was 61.77 ppm/K, while the FE model predicted an equivalent temperature coefficient of frequency (TCF) of −62.74 ppm/K with an overall coefficient of determination R2 = 0.998. In the critical cryogenic interval 130-80K the TCD fell to 47.66 ppm/K, indicating improved thermal stability at low temperature. Controlled loading (0-300 με) revealed a strain coefficient of delay (SCD) that rises from 0.53 ± 0.02 ppm/με at 300K to 1.05 ± 0.02 ppm/με at 80K. This modest sensitivity confirms that, for temperature sensing, strain is a second-order perturbation above 135K but must be compensated at deeper cryogenic levels. Overall, this work establishes a predictive multiphysics model together with repeatable wired measurements that confirm the suitability of SAW sensors for temperature and strain monitoring in extreme cryogenic environments, while also providing a baseline for future wireless implementations.« less

Fiber-optic bolometers (FOBs) based on a fiber-tipped silicon Fabry–Perot (FP) interferometric temperature sensor and a gold disk absorber have been shown to be an attractive alternative to conventional resistive bolometers for plasma radiation measurement in fusion devices. Either a high-finesse FP or a low-finesse FP can be used, each with trade-offs between noise performance and fabrication complexity. In this paper, we present an FOB design that overcomes these limitations by combining a low-finesse long silicon FP cavity with a large gold disk absorber to achieve enhanced sensitivity and noise performance without increasing the fabrication complexity and the time constant. Wemore » also demonstrated a fabrication method for the sensor head facilitated by thermal release tape and precise laser heating. Our FOB demonstrates a temperature resolution of 0.08 mK, a cooling time constant of 230 ms, and a noise equivalent power density of 0.015 W m⁻². This represents an eightfold improvement over previous high-finesse FOBs and 26-fold improvement over previous low-finesse FOBs with similar demodulation bandwidths and similar cooling time constants.« less

The plant secondary cell wall, a complex matrix composed of cellulose, hemicellulose, and lignin, is crucial for the mechanical strength and water-proofing properties of plant tissues, and serves as a primary source of biomass for biorenewable energy and biomaterials. Structural analysis of these polymers and their interactions within the secondary cell wall has been heavily relying on ¹³C-based solid-state NMR techniques. In this study, we explore the application of ¹H-detected solid-state NMR techniques for rapid, high-resolution structural characterization of polysaccharides and lignin, demonstrated on the stems of hardwood eucalyptus. We explored the use of synthesized 2D spectra to resolve centralmore » ¹H resonances and the combined application of 3D hCCH and hCHH experiments for complete resonance assignment and unambiguous identification of lignin-carbohydrate interactions. Our findings emphasize the central role of acetylated three-fold xylan conformers, rather than two-fold, in stabilizing the carbohydrate-lignin interface, with glucuronic acid sidechains in eucalyptus glucuronoxylan colocalizing with lignin, revised cellulose-lignin interactions involving uncoated microfibril surfaces, and pectin-lignin interactions indicative of early-stage lignification. These results present a novel approach for rapid structural analysis of lignocellulosic biomaterials without the need for solubilization or extraction.« less

Plants synthesize polysaccharide-based primary cell walls that possess unique microstructures and mechanical properties to accommodate plant growth and provide protection. Here, it remains challenging to assess the role of polysaccharide organization and interactions in the mechanical behavior of primary cell walls owing to their complex microstructure and highly nonlinear mechanical responses. Employing a coarse-grained molecular dynamics model developed for onion epidermal walls, this work explores the conditions under which polysaccharide assembly and interactions might play a significant role in primary cell wall mechanics. Cellulose–cellulose adhesion plays a dominant role in the wall load-bearing capacity, but when cellulose–cellulose adhesion was disruptedmore » computationally, cellulose–xyloglucan adhesion could influence the wall load-bearing capacity. Contrary to the common concept that xyloglucans mechanically tether well-separated cellulose microfibrils, xyloglucans functioned in this case as interfibrillar adhesives capable of transmitting tensile forces between cellulose microfibrils. Our findings may inform design criteria of new materials inspired by plant cell walls.« less

Interacting fermionic chains exhibit extended regions of topological degeneracy of their ground states as a result of the presence of Majorana or parafermionic zero modes localized at the edges. In the opposite limit of infinite temperature, the corresponding nonintegrable spin chains, obtained via generalized Jordan-Wigner mapping, are known to host so-called almost strong zero modes, which are long-lived with respect to any bulk excitations. Here we study the fairly unexplored territory that bridges these two extreme cases of zero and infinite temperature. We blend two established techniques for states, the Lanczos series expansion and a tensor network ansatz, uplifting themmore » to the level of operator algebra. This allows us to efficiently simulate large system sizes for arbitrarily long timescales and to extract the temperature-dependent decay rates. We observe that for the Kitaev-Hubbard model, the decay rate of the edge mode depends exponentially on the inverse temperature 𝛽, and on an effective energy scale Δ_eff that is greater than the thermodynamic gap of the system Δ.« less

The solid electrolyte interphase (SEI) is a vital component to control mass transport and selectivity in the lithium-mediated reduction of N₂ to NH₃ (Li-N₂R). Finding strategies that generate the optimal SEI, a complex network of organic and inorganic species, can potentially improve Li-N₂R performance. Here, we unravel structure-property relationships of the SEI by correlating its composition with the NH₃ faradaic efficiency (FENH3). By modifying the reaction temperature, we alter electrolyte decomposition reactions and observe changes in the SEI that explain FE_NH3 trends between electrolyte solvents. We quantify a complex reaction environment at elevated temperatures where SEI formation is counteracted bymore » etching reactions. This tradeoff leads to temporal fluctuations of FE_NH3, but the maximal FE_NH3 can reach up to 40%, the highest value reported for batch cells at ambient pressure, thus far. In conclusion, our work underscores the potential of novel electrolytes that steer SEI selectivity and, ultimately, improve Li-N₂R performance.« less

The chemical vapor infiltration (CVI) process involves infiltrating a porous preform with reacting gases that undergo chemical transformation at high temperatures to deposit the ceramic phase within the pores, ultimately leading to a dense composite. The conventional CVI process in composite manufacturing needs to follow an isothermal approach to minimize temperature differences between the external and internal surfaces of the preform, ensuring that reactive gases infiltrate internal pores before external surfaces seal. Here, this study addresses the challenge of premature pore closure in CVI processes through microwave heating. A frequency-domain microwave solver is developed in OpenFOAM to investigate volumetric heatingmore » mechanisms within the preform. Through numerical studies, we demonstrate the capability of microwave heating of creating an inside-out temperature inversion. This inversion accelerates reactions proximal to the preform center, effectively mitigating the risk of premature external pore closure and ensuring uniform densification. The results reveal a significant enhancement in temperature inversion when high-permittivity reflectors are incorporated to generate resonant waves. This microwave heating strategy is then coupled with high-fidelity direct numerical simulation (DNS) of reacting flow, enabling the analysis of resulting densification processes. The DNS includes detailed chemistry and realistic diffusion coefficients. The numerical results can be used to estimate the impact of microwave-induced temperature inversion on densification in productions.« less